CRXpower.net
May 22, 2012, 10:00:27 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
 
   Home   Help Arcade Search Calendar Login Register  
Custom Search
Pages: [1]
  Print  
Author Topic: zc tranny same as si?  (Read 639 times)
tintman976
Street Racer
*****

Karma: +0/-0
Offline Offline

Posts: 177


View Profile
« on: September 30, 2003, 12:20:37 PM »

I fucked my tranny and ordered a jdm  well i got a zc.  No prob correct?
are they geared the same
Logged
CRXpower.net
« on: September 30, 2003, 12:20:37 PM »

 Logged
OBD1 Kenobi
Post Whore
*****

Karma: +6/-2
Offline Offline

Posts: 3085


View Profile WWW
« Reply #1 on: September 30, 2003, 01:39:24 PM »

correct me if I'm wrong but ZC trannies require a intermediate shaft?

not knocking you tintman, but I think you'll be using integra axles too. You will be happy to know that it's closer geared than an Si though. Maybe rip it apart and mix and match the Si gears and ZC gears to get an even closer ratio tranny, make sure you put it in the Si bellhousing so you don't have to have integra axles.

good luck dude
Logged

   
tintman976
Street Racer
*****

Karma: +0/-0
Offline Offline

Posts: 177


View Profile
« Reply #2 on: September 30, 2003, 01:46:13 PM »

Teg axles huh great it would figure
Logged
OBD1 Kenobi
Post Whore
*****

Karma: +6/-2
Offline Offline

Posts: 3085


View Profile WWW
« Reply #3 on: September 30, 2003, 01:54:14 PM »

LoL, sorry... I'm looking for sites for info.


http://home.cinci.rr.com/mistab0ne/tranny.html

try that
Logged

   
masta shark
Post Whore
*****

Karma: +2/-0
Offline Offline

Posts: 4589



View Profile
« Reply #4 on: September 30, 2003, 04:06:00 PM »

yeah, i'm pretty sure you need Teg axles with the zc tranny, but everything else should work fine.

anyone know if the clutch is the same?
Logged

I can think of no grander expression of arrogance than, in the face of every conceivable fact, one boasts of belief to the contrary
tintman976
Street Racer
*****

Karma: +0/-0
Offline Offline

Posts: 177


View Profile
« Reply #5 on: October 01, 2003, 06:41:58 PM »

Ok the company i bought this from is www.alljapanengines.com.  Ok this is a DOHC L3 zc tranny.   I have been told by 4 other peoplethat this WILL NOT work even with the teg axles.  One guy said that i could use a 1985 honda accord se 5 speed axle for the passenger side and a 1990-93 teg axle for the drivers side.   WTF will this work  sounds like a fucked idea to me lol.  So here i set with this tranny and a lot of ?'s.   anyone have a spare si tranny for sale ?  The best part is that becouse i ordered the correct part and got sent the wrong it's MY fault....  There not willing to do anything about this.  Anyone got any advice any one to call even..

Thanks

Scott

Also did everyone get there stickers?
Logged
OBD1 Kenobi
Post Whore
*****

Karma: +6/-2
Offline Offline

Posts: 3085


View Profile WWW
« Reply #6 on: October 02, 2003, 08:05:34 AM »

Oh, fock, sorry dude. Yah everyone I know got theirs, Look at the pics from the AutoX, hehe shameless plugs everywhere.

My advice:

Sell that ZC tranny, or trade it for an Si one.

Or jus grab a DX one. The DX and Si are the same gearing, just the final drive is different. So just swap out the final drive from your broke Si tranny into the cheap DX tranny and you have yourself a good tranny.

Junkyards, junkyards, junkyards. hehe good luck dude
Logged

   
91siredrex
Post Whore
*****

Karma: +1/-9
Offline Offline

Posts: 3666



View Profile
« Reply #7 on: October 02, 2003, 10:06:56 PM »

that dude sounds right. im pretty sure its the accord axles on teh right and teg on teh left. and the zc tranny is a good tranny. u swap in the si final drive and u have the best tranny possible.
Logged

sukkers
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.15 | SMF © 2011, Simple Machines
Website hosted and maintained by Napier Communications Inc.
Page created in 0.063 seconds with 21 queries.